Dousman, WI Standby Generator Installation & Maintenance

*Estimated Read Time: 9 minutes* Power outages in Wisconsin are more than an inconvenience. Frozen pipes, flooded basements, and spoiled food are real risks. If you’re researching whole house generator sizing, you’re in the right place. This guide explains how to choose the correct kW for your home, the code and fuel details that matter, and when to go whole‑home vs essential‑circuit backup. When you’re ready, Over the Moon will size, install, and maintain the system for you. ## Why Generator Size Matters in Wisconsin Choosing the right size standby generator is about safety, comfort, and protecting your property. In Milwaukee, Waukesha, and lake‑effect neighborhoods like Wauwatosa and Germantown, outages often hit during deep freezes or summer storms. Undersizing can stall furnaces, sump pumps, or well pumps right when you need them. Oversizing can waste fuel and budget. Two hard facts guide safe sizing: 1. The National Electrical Code Article 702 governs optional standby systems and requires transfer equipment that prevents dangerous backfeed to the utility. 2. Most whole‑home standby units are rated in kilowatts and must be sized for motor starting currents. A sump pump or air conditioner can require 3 to 7 times its running watts to start. Done right, standby power keeps heat on, fridges cold, security systems armed, and medical devices powered through any outage. ## How To Estimate Your Home’s kW Needs Start with a simple load plan. You do not need perfect numbers to get close, but accuracy helps avoid nuisance trips and brownouts. 1. List essentials - Heat source: furnace blower or boiler circulators. - Refrigeration: kitchen fridge and freezer. - Water: sump pump, well pump, or ejector pump. - Cooking and lighting: kitchen circuits and general lighting. - Comfort and safety: Wi‑Fi, garage door, security system, critical outlets. 2. Add major 240‑volt loads - Central AC, electric range, electric dryer, electric water heater, hot tub, EV charger. Decide which must run during an outage. 3. Capture running watts and starting watts - Running watts are on the nameplate. Starting watts matter for motors. - Typical examples for planning: 1. Refrigerator: 150–300 running, 800–1,200 starting. 2. Sump pump: 600–1,000 running, 1,300–2,100 starting. 3. 1‑hp well pump: 1,000 running, 2,000–4,000 starting. 4. Furnace blower: 400–800 running, 1,000–1,600 starting. 5. Central AC 3‑ton: 3,500 running, 7,000–9,000 starting. 4. Apply diversity - Not every load runs at once. A skilled electrician applies demand factors and may use load‑shedding modules for AC or water heaters so the generator stays within rating. 5. Convert to kW - Total watts divided by 1,000 equals kW. Add a 20–25 percent buffer for weather, motor aging, and future appliances. Professional sizing adds power factor, voltage drop, and feeder calculations. It also confirms 240‑volt loads, phase balancing, and the best transfer switch type for your panel. ## What Common Generator Sizes Actually Power Every home is different, but these scenarios help you frame the decision. - 10–12 kW 1. Essentials in a smaller home or condo. 2. Gas furnace blower, fridge, lights, Wi‑Fi, and a sump pump with smart load‑shedding. - 14–18 kW 1. Most 2,000–3,000 sq. ft. homes with gas heat. 2. Adds a 2–3 ton AC or well pump using load management. - 20–22 kW 1. Larger homes or multiple motor loads. 2. Runs furnace, kitchen, two sump pumps, and a 3–4 ton AC with soft‑start or load control. - 24–26 kW and up 1. Whole‑home with electric range and dryer. 2. Good for homes in Waukesha, Pewaukee, or Oconomowoc with larger HVAC systems or finished basements. Generac’s popular residential sizes include 14 kW, 18 kW, and 22 kW. Pairing AC soft‑start kits and load‑shedding modules lets a properly sized unit handle heavy startup currents without oversizing. ## Fuel, Gas Line, and Placement Requirements Your generator is only as reliable as its fuel supply and installation quality. - Fuel type 1. Natural gas is common in Milwaukee County and keeps run time effectively unlimited. 2. LP works well in rural or edge communities like Sussex and Oconomowoc and needs an appropriately sized tank. - Gas line sizing 1. Standby generators often require 3/4‑inch to 1‑inch or larger piping, depending on distance and BTU rating. 2. Fuel supply must meet manufacturer flow and pressure requirements under load. We size and install gas lines in‑house so there is one accountable contractor. - Placement 1. Follow clearances to openings and property lines. 2. Set on a stable pad with proper drainage. Snow drifting off Lake Michigan can block vents, so we plan for winter access. We handle the gas line work, site prep, and electrical integration so your system is safe, quiet, and code compliant. ## Transfer Switches: Whole‑Home vs Essential‑Circuit Your transfer switch decides what gets power during an outage and how seamlessly it happens. - Service‑rated automatic transfer switch (ATS) 1. Powers the whole panel. Best for 14 kW and larger units. 2. Simple operation. The generator senses an outage and starts automatically. - Load center or essential‑circuit ATS 1. Feeds a subpanel of selected circuits. Useful when fuel or budget limits capacity. 2. Great for homes that only need heat, sump pump, fridge, lights, and internet. NEC 702 requires transfer equipment to isolate your home from the grid, preventing backfeed that endangers utility crews. Our licensed electricians size, wire, and test the ATS so it operates safely under all conditions. ## Whole‑Home or Partial Backup: Which Is Right? Pick whole‑home when any of these apply: 1. Multiple motor loads like two sump pumps or a deep well. 2. Larger families who run kitchens, laundry, and HVAC together. 3. Home offices with servers or medical equipment. Choose essential‑circuit when: 1. You have gas heat and only need core systems. 2. You want the lowest fuel and equipment cost now with an option to upgrade later. 3. The service drop, gas meter, or lot placement is restrictive. We frequently design essential‑circuit solutions for bungalows in Wauwatosa, then upgrade to whole‑home when a renovation adds square footage or an EV charger. ## Cost Factors and How To Avoid Overspending Generator projects vary because homes and priorities differ. Expect pricing to reflect: 1. kW rating and brand features - Larger engines, quiet enclosures, and advanced controllers add cost. 2. Transfer switch type and load management - Service‑rated ATS and smart modules cost more but simplify living during an outage. 3. Gas line distance and meter capacity - Longer runs or upsizing gas meters increase labor and material. 4. Site conditions - Concrete pads, trenching, or panel upgrades affect the budget. 5. Permits and inspections - Municipal permits and utility coordination are included in our turnkey pricing. Money‑saving tips: - Size to essential outcomes, not everything you could possibly run. - Use soft‑starts on AC to lower starting amps. - Plan pre‑wiring for future expansion. - Join a maintenance program to protect your warranty and reduce repair costs. ## Professional Sizing, Permits, and Compliance Turnkey matters. Here is what a professional process includes with Over the Moon: 1. Load analysis and kW modeling - We measure motor starting currents and calculate demand so the generator does not trip under real‑world conditions. 2. Detailed proposal with upfront pricing - You will see equipment, labor, permits, and any panel or meter upgrades before work begins. 3. Permitting and inspections - We coordinate with local inspectors across Milwaukee, New Berlin, Menomonee Falls, and beyond. 4. Gas line and electrical integration - Our licensed team sizes and installs gas piping and wires the ATS and service panel for safe operation. 5. Start‑up, testing, and homeowner orientation - We simulate an outage, verify voltage and frequency, and show you how the system operates. Hard fact: Our Wisconsin Electrical License is #1130645, and we are an authorized Generac dealer. That means proper parts, training, and warranty support. ## Maintenance: Keep Your Investment Ready Standby generators sit quiet for months, then must work at full power in seconds. That is why maintenance is vital. - Core tasks we perform 1. Exercise test and fault code scan. 2. Oil and filter service per manufacturer intervals. 3. Battery health test and charger verification. 4. Air filter, spark plug, and governor inspections. 5. Gas pressure and leak check. - VIP Gold Star Membership benefits 1. Three onsite visits per year with a precision tune‑up and electrical safety inspection. 2. Priority scheduling, members‑only hotline, lifetime warranty on eligible installations, and 15% savings on eligible services. Regular testing prevents failures from stale fuel, weak batteries, or stuck valves. In Wisconsin’s climate, this is non‑negotiable for reliability. ## Real‑World Examples by Home Type - City bungalow, Milwaukee, gas heat 1. Essentials plus a 2‑ton AC with soft‑start: 14–18 kW with load management. - Suburban two‑story, Waukesha, finished basement 1. Two sump pumps, fridge, furnace blower, and 3‑ton AC: 18–22 kW. - Lake home, Pewaukee or Oconomowoc, well pump 1. Well pump, fridge, furnace, dehumidifier, pier lifts off: 18–22 kW with ATS and selective shedding. - Larger home with electric range and dryer 1. If you must run all electric appliances during outages, plan 22–26 kW plus smart shedding. These are starting points. A site visit verifies panels, grounding, gas meter capacity, and placement clearances. ## Checklist: Be Ready for Your Sizing Appointment 1. List the appliances and systems you need during an outage. 2. Snap photos of your main panel, outdoor meter, and furnace nameplate. 3. Note if you have a well, septic ejector, or multiple sump pumps. 4. Share past outage issues, like basement water or spoiled food. 5. Tell us if future plans include an EV charger, hot tub, or addition. This information helps us right‑size your generator the first time. ## Why Homeowners Choose Over the Moon - Authorized Generac dealer with white‑glove service. - Single‑contractor approach, including gas line work, so scheduling is simple. - Upfront pricing after a clear sizing consultation. - Screened, certified technicians and a 100% Satisfaction Guarantee. - Fast response during storms across Milwaukee, Waukesha, and surrounding cities. Our process prevents hazards like overloading, backfeed, and carbon monoxide exposure and keeps your warranty intact. ## Ready for Whole‑Home Power in Milwaukee and Waukesha? If you want heat, pumps, and fridges running through the next storm, we are ready to help. We size, install, and maintain standby generators every week in Milwaukee, Wauwatosa, New Berlin, Menomonee Falls, Pewaukee, Muskego, Germantown, Oconomowoc, and Sussex. Get a same‑day consultation when possible and clear pricing before work begins. ## Special Offer for Standby Power Members save 15% on eligible electrical services with our VIP Gold Star Plan, plus priority scheduling and a members‑only hotline. Join today and apply your discount to your generator maintenance or qualifying electrical work. Call (262) 297-3186 or visit https://calloverthemoon.com/ to activate your membership and lock in savings before storm season. ## What Homeowners Are Saying > "Installed a whole home generator. The entire crew that was here over the last two days did an outstanding job. Thank you" > –Christopher M., Generator Installation > "They even supplied a generator (no extra charge) so we would have some electricity for things like the fridge and Wi‑Fi while the electricity had to be off. ... We are VERY pleased with our experience with Over The Moon and highly recommend them." > –Sharon S., Electrical Service > "My wish is/was to have a EZ Transfer Switch installed on furnance, to enable a backup power source for continious heat. Zach was my tech, and he was very polite/knowlegeable. ... I appreciated the concern for safety measures, etc... Thank You" > –Anita M., Transfer Switch ## Frequently Asked Questions ### How do I calculate what size whole house generator I need? Add up running watts for essentials, account for 3–7x starting watts on motors, apply diversity, then add a 20–25 percent buffer. A pro confirms with load calculations. ### Can a 14 kW generator run my AC and furnace? Often yes for gas heat with a 2–3 ton AC if you add a soft‑start and load‑shedding. Exact results depend on your blower size, AC tonnage, and total home load. ### Do I need a permit for a standby generator in Milwaukee or Waukesha? Yes. Electrical and gas permits are typically required, and inspections verify clearances, wiring, and gas line sizing. We handle permitting for you. ### What fuel is best, natural gas or LP? Natural gas is convenient where available and supports long run times. LP is ideal for rural areas with tank storage. Both work when properly sized. ### How far from the house should the generator be placed? Follow manufacturer and local code clearances from openings and property lines. We confirm placement during site evaluation to meet code and reduce noise. ## Final Takeaway Getting whole house generator sizing right protects heat, water, food, and safety during Wisconsin outages. Start with your essential loads, plan for starting watts, and use smart load management to avoid oversizing. For expert sizing and installation in Milwaukee and Waukesha, call (262) 297-3186 or visit https://calloverthemoon.com/ to schedule. Members save 15% on eligible services with our VIP Gold Star Plan. ## Schedule Your Free Sizing Consultation Call Over the Moon at (262) 297-3186 or book online at https://calloverthemoon.com/. Ask about our VIP Gold Star Plan to save 15% on eligible generator maintenance and enjoy priority service. Protect your home before the next storm hits. Over the Moon is Milwaukee’s trusted electrical team for standby power. We’re authorized Generac dealers, licensed in Wisconsin (Electrical #1130645), and our screened, certified technicians deliver white‑glove service. Members get priority scheduling, a members‑only hotline, lifetime warranty on eligible installations, and 15% savings through our VIP Gold Star Plan. We handle everything in‑house, including gas line work and code‑compliant wiring. Same‑day service when possible and a 100% Satisfaction Guarantee.

Menomonee Falls Standby Generator Installation & Maintenance Costs

*Estimated Read Time: 11 minutes* If you are pricing out a standby generator installation cost for your Wisconsin home, you want clear, local answers. This guide explains what drives pricing, how sizing works, and the benefits that matter in our climate. You will also see safety steps, maintenance expectations, and ROI. Ready for a straight estimate and professional sizing? Our licensed electricians handle the entire project, including gas line work, start to finish. ## Why Homeowners Choose Standby Generators in Wisconsin Power outages hit hardest when the temperature drops or storms roll through Lake Michigan. In Waukesha County and across Greater Milwaukee, a whole-home standby unit can protect daily life and your property. Top local benefits: 1. Prevent frozen pipes by keeping the furnace running. 2. Keep the sump pump online to avoid basement flooding. 3. Preserve food in fridges and freezers. 4. Maintain Wi-Fi, lighting, and security systems. 5. Keep medical devices powered without interruption. An automatic standby generator senses a utility outage and starts within seconds. With a properly sized Generac system, critical and comfort circuits stay on without refueling hassles. ## What Affects Standby Generator Installation Cost Every home is different. Your standby generator installation cost depends on several factors that an in-home assessment will confirm. Key cost drivers: 1. System size in kilowatts - Larger homes or more circuits need more kW. - Loads like electric ranges, AC, and well pumps increase capacity. 2. Fuel type and gas line scope - Natural gas is common in Greater Milwaukee. Propane is typical in rural areas. - Trench length, regulators, and meter upgrades affect cost. 3. Transfer switch type - Automatic whole-home transfer switches cost more than load-selective options. 4. Electrical distance and complexity - Longer conduit runs and panel upgrades raise material and labor time. 5. Site prep and pad - Concrete or composite pads, leveling, and clearances add to scope. 6. Permits and inspections - Municipal permits and utility coordination vary by city. 7. Brand, warranty, and dealer level - Authorized dealer install quality and support influence lifetime value. We provide sizing and a fixed, upfront price before work begins. No surprises. ## Typical Price Ranges You Can Expect Actual quotes require a site visit, but homeowners often ask for ballpark context. Here is how budgets usually stack up for a professional, code-compliant install with an authorized Generac dealer. Common ranges in our market: - 14–18 kW systems: Often right-sized for many Wisconsin homes with gas heat and typical loads. - 20–26 kW systems: Covers larger homes or higher-demand circuits. - Transfer switch, pad, gas line work, permits, and install labor are included in a full-service quote. Why ranges vary: - A simple gas tie-in close to the meter and a short electrical run costs less. - A service panel upgrade, long runs, or propane tank setup increases the budget. Our goal is to match the model to your lifestyle and critical loads, then deliver one complete price that covers everything from delivery to final inspection. ## Sizing Your Generator the Right Way Correct sizing is the heart of performance and cost control. Oversizing wastes money. Undersizing strains the unit and risks tripping. How we size: 1. Load interview - We list must-run items first. Heat, sump, fridge, lighting, Wi-Fi, security, medical devices. 2. Starting vs running watts - Motors need extra power to start. We calculate real inrush demands. 3. Diversity and load management - Not all circuits run at once. We plan realistic demand and smart prioritization. 4. Future planning - We ask about EV chargers, hot tubs, or finished basements you may add. Our licensed electricians then recommend the right Generac model and transfer switch so you get reliable power without overspending. ## Installation Steps: What to Expect Our process keeps your project organized and code compliant from day one. 1. Site evaluation and written proposal - We confirm clearances, gas capacity, grounding, and placement. - You receive a fixed price and timeline. 2. Pad and delivery - We prepare the pad and deliver the generator. 3. Gas line connection - We handle gas line work in-house so you work with one contractor. 4. Transfer switch and wiring - We connect the transfer switch and integrate with the main service panel. 5. Startup and testing - We test under load, set exercise schedules, and review maintenance steps. 6. Inspections - We coordinate municipal and utility inspections as required. Professional installation prevents overloading, back feeding, fires, and carbon monoxide risks. It also protects warranty coverage. ## Safety, Codes, and Permits in Our Area Local codes and manufacturer specs guide safe placement and wiring. Common checklist items include: - Clearances from windows and doors for exhaust safety. - Proper fuel piping, regulators, and leak testing. - Correct grounding, conductor sizing, and overcurrent protection. - Dedicated transfer switch to avoid dangerous back feeding. We follow Wisconsin electrical code and inspection requirements in each city. Over the Moon holds Wisconsin Electrical License #1130645, and our team is trained on Generac standards. This protects your home, your warranty, and your insurance. ## Fuel Choices: Natural Gas vs Propane Both fuels are reliable in winter. Your choice often comes down to availability and cost. - Natural gas - Continuous supply, no refills. - Usually lower operating cost. - Propane - Common where no gas main exists. - Requires tank sizing and safe placement. We confirm meter capacity or tank size during the site visit. We install and test regulators, piping, and shutoffs per code. ## The Real Benefits: Comfort, Safety, and ROI Standby generators do more than keep the lights on. In Wisconsin, the protective value is real. - Property protection - Heat stays on, so pipes do not freeze. - Sump pumps run, so basements do not flood. - Health and safety - Medical devices remain powered. - Security systems and lighting deter break-ins. - Daily life - Food stays cold. Work and school continue with Wi-Fi and devices. ROI comes from avoided damage, insurance deductibles, and home marketability. Buyers value backup power in areas prone to storms. ## Maintenance: What It Takes to Stay Ready Standby units can sit idle for months, then must run for hours without a hiccup. Preventive care keeps them ready. Core maintenance items: - Regular exercise cycle checks. - Oil and filter changes by runtime and season. - Spark plug and air filter replacement on schedule. - Battery testing and replacement when needed. - Full system test under load. We offer recurring maintenance, testing, and preventive care. Our VIP Gold Star Plan includes three onsite visits per year with precision tune-ups and an electrical safety inspection. Pricing is $249 per year, with $71 for each additional system. Members receive priority scheduling, a members-only hotline, and lifetime warranties on installations. ## Total Cost of Ownership: Save More Over Time Upfront price is only part of the story. A correctly sized, professionally installed Generac system reduces lifetime cost. Ways we lower total cost of ownership: - Right-size capacity to avoid wasted fuel. - Code-compliant gas line and wiring to prevent damage. - Proactive maintenance to extend engine life. - Fast repairs by trained techs to limit downtime. Choosing an authorized dealer means faster parts access and trained diagnostics when you need help. ## Choosing the Right Installer Pick a partner who stands behind the work and the warranty. Look for: 1. Licensed electricians who can handle transfer switches and main panel work. 2. In-house gas line capability so you have one accountable contractor. 3. Authorized Generac dealer status. 4. Upfront, written pricing and a clear scope. 5. Safety record and background-checked technicians. 6. Strong local reviews and real human support on the phone. Over the Moon meets these standards with screened, certified technicians and a 100% Satisfaction Guarantee. We provide same-day service when possible and white glove care in your home. ## Service Areas We Know Well We install and maintain standby generators across Greater Milwaukee, including: - Milwaukee, Waukesha, Wauwatosa, New Berlin - Menomonee Falls, Pewaukee, Muskego - Germantown, Oconomowoc, Sussex Local knowledge matters when planning gas lines, permits, and inspections. ## When Repair Beats Replace If your system is newer but not starting, repair may be smarter than replacement. Repair scenarios: - Battery failure or fuel supply issue - Control board fault or sensor error - Plugged air filter or worn spark plugs Replace scenarios: - Frequent failures with high repair bills - Outdated model with scarce parts - Undersized system that never meets demand Our technicians diagnose quickly and explain options so you can choose with confidence. ## How To Get a Fast, Accurate Quote The most accurate standby generator installation cost comes from a brief, on-site visit. What to prepare: 1. A list of must-run circuits. 2. A photo of your main panel. 3. Info on gas meter or propane tank. 4. Your goals for comfort and budget. We then provide a model recommendation, a full written price, and a timeline. Most installs follow a smooth one to three day plan depending on scope. ## What Homeowners Are Saying > "Installed a whole home generator. The entire crew that was here over the last two days did an outstanding job. Thank you" > –Christopher M., Whole-Home Generator Install > "OMG! This company is absolutely amazing! ... They even supplied a generator (no extra charge) so we would have some electricity for things like the fridge and Wi-Fi while the electricity had to be off. The next day we had a question, called the office, and Shaun came right over. ... We are VERY pleased with our experience with Over The Moon and highly recommend them." > –Sharon, Electrical Service > "HVAC inspection done. Very professional, honest, and personable service. Also had major electrical work done (breaker panel replaced & generator hook up). They worked hard on this and completed the job professionally. They made sure to keep me updated on their progress and are very pleasant to work with. I would highly recommend them." > –Deadeye, Generator Hookup ## Frequently Asked Questions ### How much does a standby generator installation cost in Wisconsin? Final pricing depends on size, gas line scope, electrical runs, and permits. Most homes fit 14–26 kW systems. We provide a fixed, written price after a site visit and load review. ### What size standby generator do I need? We size by your must-run circuits, starting watts for motors, and diversity. Many homes fit 14–20 kW, but larger or high-demand homes may need 22–26 kW. A load interview ensures accuracy. ### How long does installation take? Most projects take one to three days after permits and utility coordination. Timeline depends on pad prep, gas line work, and electrical distance to the panel. ### Do I need permits for a standby generator? Yes. Cities require electrical and often gas permits, plus inspections. We pull permits, meet inspectors, and ensure code-compliant placement and wiring. ### How often should my generator be serviced? Plan seasonal checks and maintenance by runtime. Our VIP Gold Star Plan provides three onsite visits per year, priority service, and lifetime warranties on installations. ## Conclusion A well-sized, professional install delivers strong value for Wisconsin homes. You now understand the key standby generator installation cost drivers, the safety steps that protect your home, and the benefits you can count on in Milwaukee and Waukesha. ## Call to Schedule Your Assessment Ready for a fixed, written quote and expert sizing? Call Over the Moon at (262) 297-3186 or visit https://calloverthemoon.com/ to schedule your in-home assessment today. Get a same-day quote when possible. Call (262) 297-3186 or book online at https://calloverthemoon.com/. Ask about our VIP Gold Star Plan with three annual visits and lifetime warranties on installations. About Over the Moon Over the Moon delivers white glove electrical service across Greater Milwaukee. We are authorized Generac dealers with Wisconsin Electrical License #1130645. Our screened, certified technicians handle full standby generator installs, including gas line work, with 100% Satisfaction Guaranteed. Members enjoy priority scheduling, a members-only hotline, and lifetime warranties on installations. With same-day service when possible and three annual tune-ups in our VIP Gold Star Plan, we keep your home safe and powered through Wisconsin weather.

Standby Generator Installation and Maintenance in Greater Merton Area

Name: Over the Moon
Address: 20711 Watertown Rd, Suite D, Waukesha, WI 53186, Brookfield, Wisconsin, 53045, US
Telephone: https://calloverthemoon.com/

Need reliable backup power? Our licensed electricians install and maintain standby generators the right way. We serve the Greater Merton area, including Milwaukee, Waukesha, and Menomonee Falls. Homeowners trust our white-glove care and clear guarantees, backed by a 4.7 rating from 1,354 reviews. Get a free second opinion and ask about VIP membership perks and lifetime installation warranties. Schedule your in-home estimate today.

Call (262) 297-3186

Our work

Project Gallery

Ensure seamless power with Over the Moon's reliable standby generator installations, blending efficiency with nature's tranquility.

Why us

Why Choose Us

Licensed electricians

Electrical License #1130645; HVAC License #1453339.

White-glove care

Floor protectors, shoe covers, gloves, deodorizer each visit.

Vetted, trained techs

Background-checked, drug-tested, and thoroughly trained.

Transparent guarantees

Free second opinions and pay only when 100% satisfied.

Proven local reviews

4.7 rating from 1,354 reviews.

Social proof

What Our Customers Say

5.0
quality

“Installed a whole home generator. The entire crew did an outstanding job.”

5.0
professionalism

“We even had them install a whole home generator. Great experience and communication.”

5.0
professionalism

“Completed major electrical work and generator hook up professionally.”

Got questions?

Frequently Asked Questions

How much does whole house generator installation typically cost?

Whole-house generator installation cost depends on generator size, transfer switch, and needed gas line work. A technician will confirm the total after an on-site assessment with upfront pricing. We install Generac standby systems and handle wiring and gas lines so you use one contractor. Our VIP Gold Star Membership saves 15% on eligible services and costs $249 per year. We also offer $100 off any electrical service. We serve Waukesha and Milwaukee.

Updated: 2025-12-24 00:00:00

Need help in Eagle, WI? Call (262) 297-3186 or book online. "Installed a whole home generator." — Christopher M.

How much does standby generator repair typically cost?

How much does standby generator repair service typically cost?

How much does it cost to install a standby generator at home?

How much does home standby generator repair typically cost?

Still have questions?

Have questions or need service? Contact our team today to discuss your needs, request a quote, or schedule an appointment.

Call (262) 297-3186

Learn more

Helpful Resources

February 16, 2026

Ixonia, WI Standby Generator Installation & Maintenance — 7 Start-Up Fixes

Estimated Read Time: 9 minutes

A storm rolls over Lake Michigan and your standby generator won’t start. Now what? In this guide, we break down the seven most...

March 30, 2026

Nashotah Standby Generator Installation & Maintenance

Estimated Read Time: 10 minutes

Whole-home outages are stressful. A well planned backup generator installation keeps heat, sump pumps, fridges, and Wi‑Fi run...

January 5, 2026

Lac La Belle, WI Standby Generator Installation & Maintenance Tips

Estimated Read Time: 9 minutes

If your generator is running but not producing power, act fast and stay safe. This guide gives you a quick, step-by-step way t...

Where we work

Where We Work

Merton

Oconomowoc

Menomonee Falls

Chenequa

New Berlin

Hartland

Ixonia

Wauwatosa

Pewaukee

Muskego

Nashotah

Dousman

Elm Grove

Delafield

Waukesha

Germantown

Eagle

Milwaukee

Wales

Lac La Belle

Sussex

Ready when you are

Schedule service today with Over the Moon.

(262) 297-3186

See all services

Project Gallery

Why Choose Us

Licensed electricians

White-glove care

Vetted, trained techs

Transparent guarantees

Proven local reviews

What Our Customers Say

5.0quality

5.0professionalism

5.0professionalism

Frequently Asked Questions

Helpful Resources

Ixonia, WI Standby Generator Installation & Maintenance — 7 Start-Up Fixes

Nashotah Standby Generator Installation & Maintenance

Lac La Belle, WI Standby Generator Installation & Maintenance Tips

Where We Work

Merton

Oconomowoc

Menomonee Falls

Chenequa

New Berlin

Hartland

Ixonia

Wauwatosa

Pewaukee

Muskego

Nashotah

Dousman

Elm Grove

Delafield

Waukesha

Germantown

Eagle

Milwaukee

Wales

Lac La Belle

Sussex

Schedule service today with Over the Moon.

5.0
quality

5.0
professionalism

5.0
professionalism